In recent years steelconcrete composite shear walls have been widely used in enormous highrise buildings. Due to high strength and ductility, enhanced stiffness, stable cycle characteristics and large energy absorption, such walls can be adopted in the auxiliary building; surrounding the reactor containment structure of nuclear power plants to resist lateral forces induced by heavy winds and severe earthquakes. This paper demonstrates a set of nonlinear numerical studies on Ishaped composite steelconcrete shear walls of the nuclear power plants subjected to reverse cyclic loading. A threedimensional finite element model is developed using ABAQUS by emphasizing on constitutive material modeling and element type to represent the real physical behavior of complex shear wall structures. The analysis escalates with parametric variation in steel thickness sandwiching the stipulated amount of concrete panels. Modeling details of structural components, contact conditions between steel and concrete, associated boundary conditions and constitutive relationships for the cyclic loading are explained. Later, the load versus displacement curves, peak load and ultimate strength values, hysteretic characteristics and deflection profiles are verified with experimental data. The convergence of the numerical outcomes has been discussed to conclude the remarks.
1. INTRODUCTION
Traditionally, reinforced concrete (RC) walls have long been adopted as an efficient lateral load resisting systems to enhance the stability and integrity of the buildings against dynamic actions such as wind, earthquakes etc. Later, steel plate walls were proposed as a promising alternative of concrete walls. Thin steel plate walls contributed in weight reduction of the structure with greater stiffness, higher ductility and enabled rapid constructions. Composite construction was then used for the structures requiring higher order of safety and reliability. RC shear walls with flanged cross sections have been theoretically, numerically and experimentally studied in the nuclear power plants. Asfur and Bruin
[1]
compared the analytical studies with the results of the test conducted by Nuclear Power Engineering Corporation (NUPEC)
[2]
to investigate the dynamic characteristics of RC shear walls. Mo and Chan
[3]
presented a softened concrete stressstrain relationship for the prediction of overall strength behavior of low rise reinforcedconcrete framed shear walls with flanged geometry under static loads. The softening parameters were found to be one of the main reasons in overestimating the ultimate strength values for highstrength concrete. Yoshio et al.
[4]
developed analytical methodology to predict the behavior of RC shear wall structures from elastic to collapse load with multiaxes seismic loading schemes using FEM technology. The methodology was proved significant for evaluating the strength margins of important structures in a nuclear power plant. Singh and Kushwah
[5]
determined the ultimate load capacity of reinforced concrete shear walls under static and dynamic loads using a three dimensional finite element. These wall units were considered to be used as safety class structures in nuclear power plants. The model was utilized to analyze a shear wall tested by NUPEC and the results have shown nice agreement
[2]
.
A number of studies have been reported on the behavior of steelconcrete composite shear walls. Tong et al.
[6]
experimentally studied the cyclic response of a composite structural system consisting of partially restrained steel frames with reinforced concrete infill walls. The gravity loads and overturning moments were assumed to be resisted by steel components whereas shear was resisted by reinforced concrete infill walls. The system was found to have enough lateral strength for the cyclic loads of seismic nature with good stiffness to control the drift. Hossain and Wright
[7]
statically tested the small scale models (one sixth scale) to study the flexural performance of the new type of composite wall consisting of concrete filled between two profiled sheets. The loaddeflection curves, strength, failure modes, strains and interaction properties were reported as outcomes. The interaction between steel and concrete was observed to influence the wall behavior. It was concluded that the rigidity of connection between sheeting and concrete core can lead to high shear resistance. The shear strength of composite wall was found to be higher than that of the individual components. Gan et al.
[8]
carried out the studies on type of shear wall formed by inserting the steel plates and steel section into the reinforced concrete walls. The investigation was conducted on a series of 1:2 scale specimens, loaded by constant axial compression and cyclic lateral forces. Such types of walls have shown quite larger shear stiffness compared to traditional reinforced concrete walls. Another type of composite shear walls formed by bolting a RC wall with a steel shear wall on one side was investigated by Zhao and AstanehAsl
[9

11]
. The study was emphasized on controlling the damage by providing a gap in the innovative composite shear wall system placed within a moment resisting steel boundary. Due to gap existence, RC wall didn’t get involved in resisting lateral loads until the drift had reached the corresponding gap value
[10]
. Theoretical and experimental studies on composite steelconcrete shear walls with vertical steel encased profiles have been presented by Dan et al.
[12]
. Five different types of shear walls with steel encased profile and one reinforced concrete wall were proposed and tested. The shear studs for the composite walls were designed to ensure zero slip. The shear walls with steel encased profile showed bending failure mode, with crushing of compressed concrete and tearing of the tensioned steel. The composite walls were found to have higher initial stiffness and energy dissipation with the increasing amount of steel
[12]
. Rahai and Fatami
[13]
presented the experimental and numerical investigation on composite shear walls, focusing on the effect of shear studs spacing variations. The results showed the reduction in the slope of loaddisplacement curves with increase in stud spacing. Up to specific studs’ spacing, the ductility of the composite unit was improved. The basic design methodology of double skin composite elements subjected to axial and bending loads has been defined by Wright et al.
[14]
. McKinley and Boswell
[15]
have developed an analytical solution for the elasticplastic behavior of BiSteel panels or double skin composite panels. Due to the continuity of the steel it was observed that such constructions can withstand larger deformations before failure. Wright and Gallocher
[16]
primarily investigated the ultimate capacity of composite walling and its benefits over traditional concepts. Omer et al.
[17]
carried out the numerical modeling and analysis of double skin composite plates. It was found that concrete core failure can fairly be reduced with increasing effect of side steel plate thickness. The steel plate skin represented an excellent solution of concrete failure when subjected to severe loadings
[17]
.
In this study, the reversed cyclic behavior of Ishaped composite steelconcrete shear walls (CSCSW) has been investigated through nonlinear numerical studies. A threedimensional finite solid element model is developed using ABAQUS. The cracking of concrete and yielding of steel has been taken into account in the material modeling to depict the actual attributes of complex shear wall structures. The analyses proceed with parametric variation in the steel thickness sandwiching the concrete panels. The details of modeling of structural components, contact conditions between steel and concrete, associated boundary conditions and constitutive relationships for cyclic loading are explained. The load versus displacement curves, peak load and ultimate strength values, hysteretic characteristics and deflection profiles are verified with experimental data. The numerical results have shown good concurrence with the experimental results. It is noticed that the effect of steel thickness is quite prominent for evaluation of restoring and deformation characteristics of composite walls under consideration.
2. NUMERICAL MODELING OF COMPOSITE STEELCONCRETE SHEAR WALLS
In order to study the behavior of composite steelconcrete shear walls under reversed cyclic loading, the numerical study is conducted. The hysteretic behavior obtained by experiment and test results
[18

19]
is used as an input in material modeling for finite element program ABAQUS. The material law, interface behavior, element type and boundary conditions used for simulation are discussed below.
 2.1 Material Modeling
 2.1.1 Concrete Constitutive Model:
The constitutive behavior of concrete is modeled using a threedimensional continuum, plasticity based damage model
[20]
. The concrete damaged plasticity model is efficiently capable of modeling concrete in all types of elements like beams, trusses, shells and in present case, especially solids. Inelastic behavior of concrete is depicted using the concept of isotropic damaged elasticity along with the isotropic tensile and compressive plasticity
[21

25]
. The formula suggested by Carreira and Chu
[26]
is adopted to calculate the compression strain curve of concrete.
where
σ_{c}
= compressive stress in concrete,
ε_{c}
= strain in concrete,
f'_{c}
= cylinder compressive strength of concrete,
ε'_{c}
= strain corresponding to
f'_{c}
and
γ
is given by:
The strain
ε'_{c}
is taken as 0.002. The stress–strain behavior of concrete in compression is assumed to be linearly elastic up to 0.4
f'_{c}
. The plastic strain is considered beyond this region to define the stress–strain relationship of concrete in the finite element model. Concrete in tension is considered as a linear–elastic material until the uniaxial tensile stress, at which concrete cracks.
Moreover,
figure 1
explains the cyclic response of concrete with the load transition phenomenon. Initially, the material behaves linearly up to the tensile failure stress
σ_{t0}
; representing the onset of microcracking in the concrete. Beyond this stress, the material propagates towards the strain softening mechanism of the cracked concrete. The failure behavior is defined by means of a post failure stress strain relation modeled by TENSION STIFFENING as the effect is more pronounced by tension side. This phenomenon also supports for the simple simulation of steelconcrete interaction effects
[20]
. During unloading and reloading, i.e. the transition of load from tension to compression, the elastic stiffness of concrete is damaged as the unloading response starts to weaken. The two damage variables,
d_{t}
and
d_{c}
(0≤
d_{t}
,
d_{c}
≤1) characterize the elastic stiffness degradation. The degradation mechanism gets complex under cyclic loadings, due to the opening and closing of previously formed cracks. As the load changes sign, the tensile cracks tend to close significantly which causes the material to recover some elastic stiffness named as stiffness recovery effect. This recovery generally characterizes the amount of the tension damage
d_{t}
due to compressive loading. The reduction in the initial elastic stiffness
E
_{0}
is generally expressed by the following expression.
Cyclic Behavior of Concrete
Upon load reversal, the recovery factors
w_{t}
and
w_{c}
were respectively used to ascertain the tensile and compressive stiffness recovery. The values for stiffness recovery factors were set as default i.e.
w_{t}
=0 and
w_{c}
=1. The unit compression recovery factor
w_{c}
causes the material to regain full stiffness with no damage. While zero values of
w_{c}
indicates no stiffness recovery. However, during tension loading, negligibly small or even no tensile stiffness may expect to recover due to preformed developed cracks. The factor that characterizes the compression damage
d_{c}
is denoted by
w_{t}
. The compressive behavior is depicted as an input using the COMPRESSION HARDENING data as a function of inelastic strain rate. The dilation angle of 30º is used to define the direction of plastic strain in the yield surface. The shear retention is not defined in the material model which makes ABAQUS to assume no effect on shear response by cracking i.e. full shear retention. This assumption is acceptable; the overall response is fairly independent of the amount of shear retention provided
[20]
. The tensile strength, Poisson’s ratio and elastic modulus and plastic strains are defined as per the compressive test results of concrete to interpret more realistic behavior
[18
,
19]
.
 2.1.2 Steel Constitutive Model
If the material modeling is incorrect, the calculation results of the static and dynamic structural response cannot be measured correctly
[27]
. For the better prediction of inelastic hysteresis behavior of steel, it is required to use such a material model that can properly simulate the cyclic behavior of the steel. Under load reversals, the loadbearing capacity of the steel member decreases as the number of load cycles increase
[28]
.
A collective steel constitutive model for structural steel found in literature
[27

30]
is used for cyclic behavior of steel. The cyclic response of steel under straincontrolled loading schemes is shown in
Figure 2
. To account for progressive hardening and softening effects
[31]
, the steel is assumed to have the bilinear kinematic hardening behavior; i.e. yielding of the steel is independent of the equivalent stress, the center of the yield surface moves in
Cyclic Behavior of Steel [20]
the stress space along with the expansion and contraction of the yield surface range. Although along with the kinematic hardening, some isotropic effects in hardening are also considered to account for the Bauschinger effect. This effect shows a reduction in the yield stress upon load reversal in the direction of plastic deformation, which has initially occurred. Kojic
[30]
demonstrates the process as; the yield stress due to deformation in compression is smaller than the yield stress previously achieved in tension. The similar behavior is noticed if the material is compressed first. This is due to the reverse propagation of the load cycle. The linear kinematic hardening component controls the effect while a nonlinear component improves the shape of the cycles
[20]
. The model is quite efficient to simulate the inelastic behavior of structural steel subjected to cyclic actions
[28]
. The input data is considered in correspondence to the tensile test results
[18]
of steel specimens discussed in later sections, to perceive more realistic behavior.
 2.2 Steelconcrete Interface
As the steel and concrete surfaces were directly adjoined in the test setup so the contact analysis procedure is developed in the FE model to simulate the experimental condition. The contact interaction option in ABAQUS is used in modeling the contact between steel and concrete in the composite shear wall by providing the geometric and mechanical properties for the interaction. First, the mechanical properties are specified and then associated with geometric features of the interaction to complete the contact assignment process. The mechanical property defined here, relates with the normal and tangential behavior. The values were assigned as default which gives rise to relatively rigid contact condition.
The ‘penalty algorithm option’ is used to define the normal behavior of the bond/contact. The default penalty stiffness with the scale factor of 0.1 is used in this manner to simulate the sticking characteristics of the interface. The ‘hard’ contact option is chosen as the pressureover closure relationship to minimize the penetration of the slave surfaces into master ones at constraint points. It does not permit the transmission of contact pressure as long as the slave and master surface nodes do not come in contact
[20]
. Furthermore, the surfaces of the two bodies are not allowed to separate in order to overcome the convergence problems and to reduce the computational time. Coulomb friction model is used to simulate the tangential behavior of the contact interaction. The software calculates the shear force between surfaces using friction coefficient and contact pressure, which are specified as ‘frictionless and hard’, respectively. The steel and concrete web are joined with the steel flange at both ends using ‘tie constraint’ option so that the steel flanges connected with composite web can act as unit. This avoids the complications up to some extent in the interaction behavior of rest of the steel concrete interfaces during application of the load.
Geometric property corresponds to the selection of adequate contact discretization technique and choice of proper master and slave surfaces involved in the interaction. The surfacetosurface discretization is used to define the contact pairs constituting the master and slave surfaces. It facilitates the bond by considering the shape of two of the respective surfaces in the constraint region. The nodes are carefully adjusted to avoid penetration of some master nodes into slave nodes. Finally, to account for real sliding in steelconcrete interfaces of composite shear wall, smallsliding approach is used for the surfaces. Further, steel plates in the flange cross sections of the shear wall are modeled as embedded regions in the concrete by using ‘embedded constraint’ option in the interaction module. Although the steel plates introduced into the flanges are expected to contribute for the overall deformation capacity of the wall. However, this technique is utilized to emphasize more on the interface behavior of externally connected steel plates rather than the embedded one.
 2.3 Element, Loading and Boundary Conditions
In the modeling of concrete core and steel plates skinned at concrete surfaces in the web and flange, solid element is chosen. In general, secondorder solid elements are more efficient for complex geometric and stressdisplacement modeling but contact pressure calculations between contact bodies may be erroneous
[32]
. In a reduced integration analysis procedure, firstorder element acquires potentially stiffer behavior with a slow convergence rate, preventing mesh locking and complexity. Hence, an incorporated reduced integration with the firstorder 3D 8node solid element (C3D8R) is used for steel and concrete contact surfaces to overcome the possible errors and to consider the cracks in tension and crippling in compression under cyclic loading. Such elements require a denser mesh for efficient and precise geometric simulations. However, while using reduced integration the model gets inherently stiffer, the tension stiffening parameters are required to be adjusted to match true experimental values
[13
,
33]
.
The numerical model under observation is fixed at the bottom to restrain each component of the shear wall in all degrees of freedom and to reflect the characteristics of the prototype. Load is simulated by applying the displacement control scheme rather than direct loading to generate cyclic behavior of the composite steelconcrete shear wall. A stepbystep procedure increasing the displacement to achieve the maximum deformation capacity of the model is used. For this purpose, a roller type boundary condition is applied on the top surface to prescribe the imposed displacements. To facilitate the proper simulation of the steelconcrete contact, the loading is managed to apply majorly on the concrete surfaces. The jumps in the displacement are applied by defining smooth ‘amplitude’ which reflects the total history data. The hexahedral finite element meshes and the interface configurations of the simulated shear walls are shown in
Figure 3
.
(a) Element Mesh and (b) Interface Element Configuration Adopted for Simulation.
Geometric and Components Details of Test Specimen CSCSW1 [18,19]
3. SUMMARY OF TEST
Four identical Ishaped composite steelconcrete shear wall (CSCSW) specimens subjected to reverse cyclic loading were tested. Each specimen consists of a hybrid web and two flanges at its ends, supported by 1150 mm thick base slab. Horizontal displacement controlled loading to the shear walls was applied through 800 mm thick concrete slab over the top, acting as a boundary condition. Both base and top slabs have the plan dimensions of 4000 mm x 1500 mm and 2400 mm x 1500 mm, respectively. Moreover, steel plates were embedded in the flanges to strengthen the concrete. All the experimental models were geometrically symmetrical; besides, thickness of concrete was kept same in all test specimens. The only geometric variable was the steel thickness provided in the flanges of specimens CSCSW1, 2 and 3 whereas web steel thickness was changed in the specimen CSCSW4 as an expectance to notice the effect. The type of reversed
Thickness of Structural Components used.
Thickness of Structural Components used.
cyclic lateral displacement can be considered as another variable because ultimate and failure values were supposed to be different based on deformation capacities of the test models.
Table 1
shows the associated thickness of the structural components and other geometric details of the test specimen are shown in
Figure 4
.
The standard strength tests were performed to grasp practical deformation behaviors of both steel and concrete. The strength properties of structural steel were obtained from the tensile test and the cylinder compression test showed the 28 days compressive strength of different concrete specimens in
Table 2
and
Table 3
, respectively. These test results helped in depicting the strength and deformation characteristics of steel and concrete and to generate the simulation input properties of both materials as well.
Since no standard reversed cyclic test procedure is available for testing composite steelconcrete shear walls, the lateral load was applied at a quasistatic rate in displacement controlled cycles considering cracking, yielding and ultimate state as the major states. All test specimens were incrementally loaded using a hydraulic actuator. The load cells were used to calculate the reactions. Linear transducers and strain gauges were placed in the middle top of the web to monitor the inplane horizontal displacement and sequence of the yielding process. Initially, the process starts with slow loading and complete unloading. Subsequently, the test walls were subjected to high loads until the ultimate deformation capacity and failure point could be attained. At each incremental loading state, a constant load was maintained for a few seconds in order to measure and record the load, displacement response of the composite shear walls.
Tensile Test Results of Steel
Tensile Test Results of Steel
Cylinder Compression Test Results of Concrete
Cylinder Compression Test Results of Concrete
4. RESULTS AND DISCUSSIONS
The finite element analyses give comprehensive picture of the overall load deformation behavior of the simulated composite shear walls from elastic to ultimate load. The lateral displacements and reactions are noticed at a particular node on the middle top of all the shear walls to depict the proportioned response. However, the comparative numerical loaddisplacement envelope/skeleton curves, the cyclic behavior of numerical models and prototypes, maximum and ultimate load concurrence with the test results reported by Lee
[18]
are primarily discussed in this section.
 4.1 Numerical Results
The numerical studies are performed to predict the nonlinear behavior, structural response and loadbearing capacity of the composite steel–concrete shear walls. Those results will later be compared with the experimental values. The results from the numerical analysis are the values of the displacements, the maximum and ultimate exhibited loads. The hysteretic loops and the overall skeleton curves are used to present and validate the outcomes.
The specimens (CSCSW1 to 4) with the difference in the steel thickness show quite similar deflection behavior. The comparisons between the horizontal loads (P) versus lateral displacement (Δ) envelope curves obtained from the finite element analysis are shown in
Figure 5
.
The varying deformation capacity of the shear wall numerical models can be clearly observed as the steel thickness is changed. The maximum resistance is offered by specimen CSCSW1 with 6.0 mm and 3.2 mm thick steel plates provided in flange and web, respectively. The wall displaces not more than 7.5 mm and exhibits up to 5000 KN of approximate restoring load. Although the deformation trend is similar but the shear walls seem to
Comparative P Versus Δ Envelope Curves from Numerical Analysis.
slightly lose the resistance as the steel thickness decreases from 6.0 mm to 4.5mm and further, if reduced to 3.2 mm in the flanged cross sections of the composite wall units, CSCSW2 and 3 respectively. Moreover, the result comes out to be clearer if the greater amount of steel is provided in the web rather than the flanged parts. Accordingly, for specimen CSCSW4 about 6.0 mm thick steel is compositely used with the concrete web whereas on either side, 3.2 mm thick steel is used in flanges. The provisions are truly converse to model CSCSW1 but it is quite evident to observe the fact that the model show appreciable load bearing capacity which can be practically cost effective due to less use of steel in the web as compared to two flanges. Hence, the skeleton curves show better comparative structural behaviors of the simulated shear wall models. Next section presents the comparison of numerical results with the experimental results available in literature
[18
,
19]
. Moreover, the section below discusses the step by step comparative hysteretic cyclic behavior, overall skeleton behavior and compatibility of the numerical approach with the tested specimens.
 4.2 Comparison with Experimental Data
Figure 6
(a) shows the hysteretic cyclic curves of the numerical simulation and the experiment under ultimate load cycle. As illustrated before, the structural deformation characteristics of all the specimens are observed to be similar, so specimen CSCSW1 is generally considered for discussions.
The comparison between the numerical skeleton curves shown above, magnifies the stable behavior up to elastic limit. The experimental result lies within the boundary of numerically simulated curve with the nice effect of pinching and softening attributes. Whereas, the cyclic loop obtained from finite element analysis exhibits the softening mechanism upon load reversal but deprived of pinching
Comparative Hysteresis Loop under Ultimate Load Cycle
phenomenon. This is because of the ambiguities in the accurate modeling of the top support when the steel and concrete are connected which causes the complexity of the interaction. Another reason could be the difference in the assumed numerical bilinear behavior of the steel, from the actual behavior. Such situations had made the solid element unable to depict the required behavior. The bond behavior between steel and concrete is one of the prime aspects to control combined pinching. However, well predicted overall hysteretic response in terms of the skeleton curve is shown in
Figure 6
(b). The curve obtained by the simulation shows nice agreement of the cyclic response from elastic to ultimate load. The initial stiffness seems to be efficiently evaluated with a bit underestimation of load values during ultimate and end load cycles but still can be accepted.
Based on the accuracy and concurrent nature of skeleton curves, all the shear wall models are validated with the experimental loaddisplacement envelope curves as shown in
Figure 7
. It may be noted that the uniaxial test results were used to generate the properties of steel of different thickness.
Figure 7
(a), (b), (c) & (d) shows the simulated results of specimen CSCSW1, 2, 3 & 4 respectively, compared with the corresponding tested specimens. The finite element curves correspond well with the experimental data unless the behavior seems to be slightly under and overcalculated at some points. Comparatively, higher values are predicted by the numerical computations whereas the general behavior lies under the experimental envelopes.
Tables 4
and
5
show the maximum and ultimate load values measured by experiment and predicted by finite element software ABAQUS, in tension and compression respectively. The ultimate strength is approximated as the 80 percent of the maximum load exhibited by the composite shear walls. The convergence of the numerical approach
Comparison between Experiment and Numerical Skeleton Curve
Comparison between Experimental and Numerical Skeleton Curves
Comparison between Experimental & Numerical Strength Values in Tension
Comparison between Experimental & Numerical Strength Values in Tension
Comparison between Experimental & Numerical Strength Values in Compression
Comparison between Experimental & Numerical Strength Values in Compression
was made sure by using Newton’s iterative method which involves an automatic load increment process. If the convergence was not achieved, the increment was minified by a certain prepossessed ratio. The solution was checked until convergence with the several repetition of process for the predefined number of iterations
[20]
.
5. CONCLUSIONS
The present approach provides a practical way to model complex geometry of Ishaped steelconcrete composite shear walls of the nuclear power plants by using ABAQUS. This study has discussed the numerical and experimental attributes of the shear walls and presented parametric effects of the different steel thickness of the walls on the lateral resisting capacities.
The nonlinear cyclic behavior of the shear walls with steelconcrete acting together is investigated with reference to the earlier test data. The predicted load versus deformation curves, peak loads, ultimate strength values and deformation profiles are compared with the experimental results using skeleton curves to check the compatibility of the technique.
A good agreement is shown between the numerical and experimental skeleton curves as a response of reversed loadings. It is noticed that the deformation capacity of the shear walls rises with the increasing steel plate thickness, skinned at the concrete surfaces. Moreover, the use of steel in the web rather than the two flanges can lead to a costeffective solution for the lateral force resisting composite shear walls, as the approximately same deflection response has been observed in both cases. Although the shear walls are carefully modeled for simulation to get a response closed to experimental behavior, some differences have been seen amongst the results. Related to cyclic loop, lack of pinching effects is observed and discussed in comparison with the experimental hysteresis curve due to the heavy geometry, complex bond behavior of the walls, which generally cannot be depicted using the solid elements.
Acknowledgements
This research was supported by the Ministry of Knowledge Economy and Korea Institute of Energy Technology Evaluation and Planning (KETEP) as a part of the Nuclear R&D Program (No. 20101620100230). The authors would like to express their appreciation for the financial support.
Asfura A.P.
,
Bruin W.M.
1997
“Dynamic behavior of a shear wall: comparison between test and analyses”
Transactions of 14th International Conference on Structural Mechanics in Reactor Technology
Lyon, France
SMiRT 14HKW/7
Nuclear Power Engineering Corporation
Specification report of seismic shear wall ISP on NUPEC’S seismic ultimate dynamic response testSeptember 1994
Tokyo, Japan
NUSSWIPD009
Mo Y.L.
,
Chan J.
1996
“Behavior of reinforcedconcreteframed shear walls”
Nuclear Engineering and Design
166
55 
68
Yoshio K.
,
Nishikawa T.
,
Takiguchi K.
,
Maekawa K.
2007
“Ultimate strength of reinforce concrete shear walls under multiaxes seismic loads”
Nuclear Engineering and Design
237
1307 
1314
Singh R.K.
,
Kushwaha H.S.
1997
“Ultimate load capacity of reinforced concrete shear wall for static and dynamic loads”
Transactions of 14th International Conference on Structural Mechanics in Reactor Technology
Lyon, France
SMiRT 14HKW/14
Tong X.T.
,
Hajar J.F.
,
Schultz A.E.
,
Shield C.K.
2005
“Cyclic behavior of steel frame structures with composite reinforced concrete infill walls and partially restrained connections”
J. Constr. Steel Res.
61
531 
552
DOI : 10.1016/j.jcsr.2004.10.002
Hossain A.K.M
,
Wright H.D.
2004
“Experimental and theoretical behavior of composite walling under inplane shear”
J. Constr. Steel Res.
60
59 
83
DOI : 10.1016/j.jcsr.2003.08.004
Gan C.J.
,
Lu X.L.
,
Wang W.
2008
“Seismic behavior of steel plate reinforced concrete shear walls”
14th World Conference on Earthquake Engineering
Beijing, China
14 WCEE
Zhao Q.
,
AstanehAsl A.
2004
“Cyclic behavior of traditional and innovative composite shear walls”
13th World Conference on Earthquake Engineering
Vancouver, Canada
13 WCEE
Zhao Q.
,
AstanehAsl A.
2007
“Seismic Behavior of Composite Shear Wall Systems and Application of Smart Structures Technology”
Steel Structures
7
69 
75
Dan D.
,
Fabian A.
,
Stoian V.
2011
“Theoretical and experimental study on composite steelconcrete shear walls with vertical steel encased profiles”
J. Constr. Steel Res.
67
800 
813
DOI : 10.1016/j.jcsr.2010.12.013
Rahai A.
,
Hatami F.
2009
“Evaluation of composite shear wall behavior under cyclic loadings”
J. Constr. Steel Res.
65
1528 
1537
DOI : 10.1016/j.jcsr.2009.03.011
Wright H.D.
,
Gallocher S.C.
1995
“The Behaviour of Composite Walling under Construction and Service Loading”
J. Constr. Steel Res.
35
257 
273
DOI : 10.1016/0143974X(94)00051I
Omer A.A.
,
Mohamedien A.R.
,
Agour A.A.
,
Yones M.M.
2009
“Modeling and Analysis of Double Skin Composite Plates”
13th International Conference on AEROSPACE SCIENCES & AVIATION TECHNOLOGY
Cairo, Egypt
ASAT13
Lee SJ.
2007
“Second Year Report for Characteristics of SC Wall”
Ajou University
Suwon, Korea
Hong SG.
,
Lee SJ.
,
Lee M.J.
,
Lee E.
,
Kim W.
2011
“Shear Strength of Composite SteelConcrete Walls with Vertical Ribs”
fib Symposium PRAGUE, Composites and Hybrids, session 54
2009
ABAQUS, ABAQUS/standard, version 6.8
ABAQUS, Inc.
Pawtucket, R.I
Lubliner J.
,
Oliver J.
,
Oller S.
,
Onate E.
1989
“A PlasticDamage Model for Concrete”
Int. J. Solids Structures
Vol. 35, 1995, pp. 257273.
25
299 
326
DOI : 10.1016/00207683(89)900504
Oller S.
,
Onate E.
,
Oliver J.
,
Lubliner J.
1990
“Finite Element Nonlinear Analysis of Concrete Structures using a ‘PlasticDamage Model’ ”
Engineering Fracture Mechanics
35
219 
231
DOI : 10.1016/00137944(90)90200Z
Oller S.
,
Onate E.
,
Miquel J.
,
Botello S.
1996
“A Plastic Damage Constitutive Model for Composite Materials”
Int. J. Solids Structures
33
2501 
2518
DOI : 10.1016/00207683(95)001611
Cicekli U.
,
Voyiadjis G.Z.
,
Abu AlRub R.K.
2007
“A plasticity and anisotropic damage model for plain concrete”
Int. J. Plasticity
23
1874 
1900
DOI : 10.1016/j.ijplas.2007.03.006
Carrreira D.J.
,
Chu K.H.
1985
“Stressstrain relationship for plain concrete in compression”
ACI Struct. J.
82
(11)
797 
804
Wan S.
,
Loh C.H.
,
Peng S.Y.
2001
“Experimental and theoretical study on softening and pinching effects of bridge columns”
Soil Dynamics and Earthquake Engineering
21
75 
81
DOI : 10.1016/S02677261(00)000737
White C.S.
,
Bronkhorst C.A.
,
Anand L.
1990
“An improved isotropickinematic hardening model for moderate deformation metal plasticity”
Mechanics of Materials
10
127 
147
DOI : 10.1016/01676636(90)900239
Kojic M.
,
Bathe K.J.
2005
“Inelastic analysis of solids and structures”
Springer
New York
Lu H.
,
Han L.H.
,
Zhao X.L.
2009
“Analytical behavior of circular concretefilled thin walled steel tubes subjected to bending”
ThinWalled Structures
47
346 
358
DOI : 10.1016/j.tws.2008.07.004